1. See Detail

Electrical Kiosk Single Door with seal (1000x500x300mm)

SKU
102211
In stock
Quick Overview

Robust and weather-resistant Electrical Kiosk Single Door with seal suitable for electrical and commercial installations inside or outside.

Made from glass-reinforced polymer.

This kiosk is supplied with a triple lock system. Please note this kiosk is supplied as flat-packed but the backboard is not included.

Dimensions

  • Height: 1066mm
  • Width: 504mm
  • Depth: 300mm

Colour

  • Light grey colour (Ral 7035)
£351.20 £292.67

    Robust and weather-resistant Electrical Kiosk Single Door with seal suitable for electrical and commercial installations inside or outside.

    Please note - this kiosk is delivered as flat-packed but the backboard is not supplied with this product. Backboards are available to buy as an optional extra. To purchase a backplate for this product please visit Backplate 10653.

    Dimensions

    • Height: 1066mm
    • Width: 504mm
    • Depth: 300mm

    Specifications

    • Electromagnetic compatibility is ideal for protecting internal electronic communication

    • Suitable for low-voltage switchgear and control gear assemblies, meters, compressors, etc

    • Will not corrode, weather-resistant

    • Compliant with IEC 62208 (2011) empty enclosures for low voltage switchgear
    • High impact resistance up to 20 Kilojoules (IK10)

    • Double insulation and electrically non-conductive (1000V)

    • Triple lock system supported by non-corrosive vertical bars

    • Door hinges on right, 180º opening

    • Easily cleaned and can be painted

    • Constructed from GRP

    • Supplied with hinges, lock and key

    • Polyester back mounting plate (optional) available

    • Supplied in light grey colour (Ral 7035)

    • Suitable for use in temperatures ranging from -30ºC to +70ºC

    • Made from non-hygroscopic material ensuring minimum water absorption

    • Constructed from halogen-free and self-extinguishing material

    • UV protected

    Fitting instructions

    Full assembly instructions are supplied with this product and are also available below.

    1. Assemble the 2 sides first. Ensure the side with the black seal is at the right-hand side, front-facing. The pre-drilled holes with inserts are to be kept at the back of the base plate.
    2. Insert the screws to attach the sides to the base, do not fully tighten the screws at this stage. Turn the kiosk around, the back of the kiosk facing you.
    3. Apply the sealant tape 8x8mm to the base rear side of the base plate, the rear wall will be mounted over this seal. Apply the second half of the sealant tape 8x8mm to the top of the backplate.
    4. Assemble the backplate to the sides, inserting screws, again do not fully tighten at this stage at 4 corners.
    5. Insert longer dowels at the top of the backplate.
    6. Insert the top plate.
    7. Insert the 4 screws to attach the top plate to the sides.
    8. Fully tighten all of the screws throughout the kiosk.
    9. Insert the backplate and tighten screws.
    10. Apply sealant around 3 sides - bottom, left and top of the frame. Seal location is shown in the drawing.
    11. To attach the door, push down the bottom hinges, it will be placed in the groove located at the bottom corner and top corner. Hinges to be turned 90⁰ to lock in place.
    12. Push in the brass fitting and slide the lock cover-up, turning clockwise with the key and pull out the handle.
    13. Close the door as normal pulling down the handle to lock it in place.

    Related videos

     

    More Information
    Height (mm)1000
    Width (mm)500
    Depth (mm)300
    Write Your Own Review
    You're reviewing:Electrical Kiosk Single Door with seal (1000x500x300mm)
    Ask a Question